Crucial Embroidery Placement with Success!

Often placement is crucial to embroidery success and little bit of planning will make your embroidery look professional. I recommend printing templates of your design so you can see it in actual size. Once the template is printed, audition it on the garment. In this case, it’s a small flower for a collar point.Collar2BL

Take your time with the placement and try different positions. It’s helpful to use a digital camera (or your phone!) to take a photograph of the placement. Every time you move the template take another photograph.Collar3BL

Do this a couple of times and then review the images on the camera. You’ll quickly know which one is the most pleasing.  Tape the template to the collar. Spray the wrong side of the collar with temporary adhesive.

Hoop stabilizer (tear-away, cut-away or wash away depending on your fabric and design).  To achieve perfect placement, use PAL, the Perfect Alignment Laser. Place the hoop on a flat surface and turn on PAL. Align the beams with the horizontal and vertical markings on the hoop.Collar5BL

Slip the collar over the stabilizer aligning the template’s crosshair with the beams.  Finger press the collar to the stabilizer. For added security, you can always add tape to the edges.Collar6BL

Carefully transport and attach the hoop to the machine, retrieve the design and verify the needle is perfectly aligned with the template’s crosshair.  Remove the template and embroider the design.

Using a template, camera and laser ensures a professional finish on your embroidery. What tools do you use when placement is crucial?

 

9 Comments on Crucial Embroidery Placement with Success!

  1. Shirley Clark
    May 11, 2016 at 10:22 pm (2 years ago)

    I always print out a template of a design and use the trace button on my machine. Plus I check the needle position. Works every time!

    Reply
  2. Ruth Margaret Dailey
    May 12, 2016 at 5:26 pm (2 years ago)

    How can I hoop a baseball cap for embroidery on my Quattro 6000, a single needle machine?

    Reply
  3. Karen W
    May 13, 2016 at 2:45 pm (2 years ago)

    Sometimes the weight of the item will shift things when moving to the machine – even with tape, although painter’s or masking tape probably has the strongest hold. So, I place my hoop over a padded surface & insert a short sequin or a straight pin at 2-3 points well away from embroidery area. Even better, use longer quilting pins, which allow for easing the point back up thru the stabilizer to secure it well. There is no substitute for double-checking needle position! Double-check everything before pressing “start”!

    Reply
  4. Karin C
    May 13, 2016 at 10:26 pm (2 years ago)

    Usually, I just eyeball it….then I check it with a centering ruler… it has a 0 in the middle and goes out to 4 inches on either side. I line it up so that the same hashmark is hit on both sides, then move my needle to the 0. Most of the time, I’m either dead on or about 1/8th inch off one way or the other. For horizontal and vertical alignment, I’ll draw a chalk line & line that up on the hoop’s hashmarks, similar to the PAL laser lines.

    Reply
    • Christine
      May 14, 2016 at 6:20 am (2 years ago)

      This was esp good comment

      Reply
  5. Sara Redner
    May 14, 2016 at 3:38 pm (2 years ago)

    I love to embroider on sweatshirts and tee-shirts. Having the design hit the wrong spot on a shirt can be embarrassing so I almost always print out the template so I can be sure I get it in the right place.

    Reply
    • Bruce
      April 21, 2017 at 11:49 pm (2 years ago)

      That is what I also did. Printing the design to make sure I get it in the right place.

      Bruce, https://www.printavo.com

      Reply
  6. Joan Shriver
    May 17, 2016 at 6:35 pm (2 years ago)

    I always embroider a test embroidery. I cut it out for placement, instead of printing out a template. I always save the test embroidery for future use.

    Reply
  7. Marcia
    June 2, 2016 at 11:23 pm (2 years ago)

    What do I need to print a template? I don’t have any design software. Is there a way without buying software?

    Reply

Leave a reply to Ruth Margaret Dailey Cancel reply

Your email address will not be published. Required fields are marked *

Comment *