Searching for "block of the month"

My Block Piecer Block of the Month: Block 4: T Block Sewing Instructions

My Block Piecer
Block of the Month: Block 4: T Block
Sewing Instructions

Block 4 is a two-unit block in the My Block Piecer Sampler Block of the Month. My Block Piecer splits some blocks into smaller units when a patch shares seam allowances with more than one patch. We’ll piece each of the units in the hoop. Then the units will be removed from the hoop and sewn together on the sewing machine with ¼” seam allowance.

T Block A
Hoop tear-away stabilizer in a large hoop. Load the first unit, T Block A into the hoop and move it towards the top to make room for T Block B (or a second repeat of T Block A if you are doing multiples). Stitch color 1, the placement guide.

 

Place patch 1 fabric, right side up, in patch 1. Stitch color 2, the tackdown.

Place patch 2 fabric, right side down, over patch 1, align the raw edges. Stitch color 3, the seam.

Flip patch 2 open and finger press the seam. Stitch color 4, the tackdown of patch 2.

Place patch 3 fabric, right side down, over patch 2, align the raw edges. Stitch color 5, the seam.

Flip patch 3 open and finger press the seam. Stitch color 6, the tackdown of patch 3.

Place patch 4 fabric, right side down, over patch 3, align the raw edges. Stitch color 7, the seam

Flip patch 4 open and finger press the seam. Stitch color 8, the tackdown of patch 4.

Place patch 5 fabric, right side down, over patches 1 and 3, align the raw edges. Stitch color 9, the seam.

Flip patch 5 open and finger press the seam. Stitch color 10, the tackdown of patch 5.

Place patch 6 fabric, right side down, over patches 4, align the raw edges. Stitch color 11, the seam.

Flip patch 6 open and finger press the seam. Stitch color 12, the tackdown of patch 6. T Block a is complete.

If making multiples of Block 4 for the large quilt, stitch three more repeats of T Block A.

 

T Block B

Retrieve T Block B. Stitch color 1, the placement guide of T Block B, on hooped stabilizer.

Place patch 1 fabric, right side up, over patch 1. Stitch color 2, the tackdown.

Place patch 2 fabric, right side down, over patch 1, align the raw edges. Stitch color 3, the seam.

Flip patch 2 open and finger press the seam. Stitch color 4, the tackdown of patch 2.

Place patch 3 fabric, right side down, over patch 2, align the raw edges. Stitch color 5, the seam.

Flip patch 3 open and finger press the seam. Stitch color 6, the tack down.

Place patch 4 fabric, right side down, over patch 3, align the raw edges. Stitch color 7, the seam.

Flip patch 4 open and finger press the seam. Stitch color 8, the tack down.

Place patch 5 fabric, right side down, over patch 4, align the raw edges. Stitch color 9, the seam.

Flip patch 5 open and finger press the seam. Stitch color 10, the tack down.

If making the large quilt, stitch four repeats of T Block B (three fit in an 8” x 8” hoop).

Remove the units from the machine trim the units on the outside stitch line. If making the larger quilt, make a total of four blocks and set them aside. It’s fun to play with different layouts but it might be wise to wait until all blocks are made to finalize the layouts.

Created by Nancy Stansbury

 

My Block Piecer Block of the Month: Block 4 T Block Software Instructions

My Block Piecer
Block of the Month: Block 4 T Block
Software Instructions
By Nancy Stansbury

This ongoing Block of the Month series was designed to inspire you to learn new techniques using My Block Piecer.  As a reminder, the first Saturday of every month will feature the software lesson using My Block Piecer.  The following Wednesday will feature the sewing lesson.

  • You are free to adapt the block to a size of your preference.
  • A free trial of My Block Piecer is available if you’d like to try it before you buy it.  Note the “Save” feature is deactivated until the software is purchased.
  • Interested in learning more about My Block Piecer and other Inspirations Software?  Join us at an Inspirations Event.  Click the Events link for events near you.
  • If you’re late to the Block of the Month “party” have no fear!  Start with Block 4 or spend a little time catching up.

Let’s continue the journey of learning and creativity!


    1. Open MBP.
    2. Click on Create a New Design.
  1. If the units for the ruler on the design page show mm, Right Click on either one of the rulers on the Design Page, and Click on Inches.
  2. Right Click on either ruler again and click on Grid Settings.
    1. Check marks by:
      1. Maintain aspect ratio
      2. Snap to grid.
    2. Set Horizontal spacing to 0.25.
    3. Click OK.
  3. Click on the Block Icon.

    1. Enter T Block in the Find box at the bottom of the window (DO NOT CLICK THE ENTER KEY).
    2. Click on the Down green arrow.
    3. Click OK to place the block on the design page.
  4. In the Properties Window on the right side of the screen click on the Transform icon.

    1. Have Maintain aspect ratio checked.
    2. Change the Width to 6.
    3. Click Apply.
  5. Click on the Reorder icon.
    1. Click on each patch of the block to number them as show the illustration below.
    2. Right Click to end the numbering. The numbers will disappear but the numbering is still there.
  6. Click on the Select icon and draw a box around patches 1 through 6, the top third of the block.
    1. Select a 200mm x 200mm hoop or similar for your machine.
    2. Click the Auto Build button. If there are two units showing in the right box, the block part has not been created with only one unit.
    3. Right Click in the window on the right side (with the numbers) and Click Reset.
    4. Holding down the CTRL Key, Click on the 1 and 2.

      1. Right Click and Group.
      2. Holding down the CTRL Key, Click on unit and 3.
      3. Right click and group.
      4. Repeat ii and iii for patches 4 and 5.
      5. DO NOT CLICK AND GROUP THE LAST NUMBER.Click on the Workflow icon.

  7. Click Preview.
  8. Click Save.
    1. Click on Create a New Folder icon and name it Block 4.
    2. Double Click on the folder to open it.
    3. In the File name box enter T_BlockA.
    4. Save as type select the compatible format for your machine (pes).
    5. Click Save.
    6. A window will open showing you the files that have been created.
      1. T_BlockA_001.pes.
      2. T_BlockA _artwork.c2s.
      3. T_BlockA _preview.pdf.
    7. Close the file window.
    8. Close the Save window.
  9. Click on the Select icon and draw a box around the remaining patches.
  10. Click on the Workflow icon.

    1. The numbers have been changed to 1-5.
    2. Select a 200mm x 200mm hoop or similar for your machine.
    3. Click the Auto Build button. If there are two units showing in the right box, the block has not been created with only one unit. If there is only 1 unit, go to Step14.
    4. Right Click in the window on the right side (with the numbers) and Click Reset.
    5. Holding down the CTRL Key, Click on the 1 and 2.
      1. Right Click and Group.
      2. Holding down the CTRL Key, Click on unit and 3.
      3. Right click and group.
      4. Repeat ii and iii for patch 4.
  11. Click Preview.
  12. Click Save.
    1. In the File name box enter T_BlockB.
    2. Save as type select the compatible format for your machine(pes).
    3. Click Save.
    4. A window will open showing you the files that have been created.
      1. T_BlockB_001.pes.
      2. T_BlockB _artwork.c2s.
      3. T_BlockB _preview.pdf.
    5. Close the file window.
    6. Close the Save window.
  13. Click the Select icon and draw a box around the entire block, OR Enter CTRL-A to select all of the block.
  14. Click the Cutter icon.

    1. Seam allowance default is .25”. Normally I change this to 0.4” or 0.5”, to make it easier to place the fabric pieces no matter which output format I choose.
    2. How you are going to create the fabric pieces for the block, will determine which file format (hoop) to choose for the templates.
      1. If manually cutting the fabric pieces, select the Paper Letter 210×279.
      2. If using the Scan and Cut, select Brother SCN 12x12”.
      3. If using the Silhouette, select Silhouette 12x12”.
    3. Unclick Optimize Orientation if using a directional fabric.
    4. Click Apply.
    5. Click Save
      1. In File name enter T_Block Templates.
      2. Select the format of choice from the Save as Type field.
      3. Click Save.
      4. The Following Files have been created.
        1. T_Block templates.
        2. T_Block templates_preview.pdf.
      5. Close the files window.
      6. Close the Cutter window.
  15. Click on Create a New Design.Note: When using the Merge to open a file, SAVE is actually a SAVE AS and the original file is not overwritten.
  16. Click on the Hoop icon and select a 200mmx200mm hoop or similar for your machine.
  17. Click on File, Merge.
    1. Locate the file T_BlockA_001.c2s.
    2. Double click on the file to open OR click on the file name, then Click OK.
  18. Move to upper part of the hoop.
  19. Click on File, Merge.
    1. Locate the file T_BlockB_001.c2s.
    2. Double click on the file to open OR click on the file name, then Click OK.
  20. Move to the bottom of the hoop
  21. Click Save.
    1. In the name field enter T-Block.
    2. In the Save as type enter the format for your specific machine.
  22. Print the templates, or prepare your fabric and send the templates to your cutter.
  23. Load the design in your machine and create the two portions of this block.
  24. Manually sew the two pieces together on your sewing machine.

 

Block of the Month: Block 3 – Four Triangles – Sewing Instruction

My Block Piecer
Block of the Month : Block 3 Four Triangles
Sewing Instructions

Block 3 is our first two-unit block in the My Block Piecer Sampler Block of the Month. My Block Piecer splits some blocks into smaller units when a patch shares seam allowances with more than one patch. The 4-Triangle block consists of four half-square triangles. We’ll piece two units of two half-square triangles in the hoop. Then the units will be removed from the hoop and sewn together on the sewing machine with ¼” seam allowance.

Hoop tear-away stabilizer and stitch color 1, the placement guide of Unit 1.

Place patch 1 fabric, right side up, in patch 1. Stitch color 2, the tackdown.

Place patch 2 fabric, right side down, over patch 1, align the raw edges. Stitch color 3, the seam.

Flip patch 2 open and finger press the seam. Stitch color 4, the tackdown of patch 2.

Stitch color 5, the placement guide of Unit 2.

Place patch 3 fabric, right side up, over patch 3. Stitch color 6, the tackdown.

Place patch 4 fabric, right side down, over patch 3, align the raw edges. Stitch color 7, the seam.

Flip patch 4 open and finger press the seam. Stitch color 8, the tackdown of patch 4.

Remove the block from the machine and hoop. Trim the block on the outside stitch line.

Cut the stabilizer, separating the two units. Examine the block and make sure you cut the units between the raw edges, not the sewn seam.

Align the center seams of the two units and insert a pin horizontally into the ditch of the seam to keep it aligned.

For additional security, pin the units together.

Sew with ¼” seam allowance on the sewing machine.

You could opt to stitch the two units together in the hoop by loading the second design, Blk3Triangle_002.

If making the larger quilt, make three more blocks and set them aside.

It’s fun to play with different layouts but it might be wise to wait until all blocks are made to finalize the layouts.

Created by Nancy Stansbury

 

[/toggle]

Block of the Month: Block 3 – Four Triangles – Software Instruction

My Block Piecer
Block of the Month : Block 3 Four Triangles
Software Instructions
By Nancy Stansbury


We hope you are enjoying this Block of the Month series.  As a reminder, the first Saturday of every month will feature the software lesson using My Block Piecer.  The following Wednesday will feature the sewing lesson.

  • You are free to adapt the block to a size of your preference.
  • A free trial of My Block Piecer is available if you’d like to try it before you buy it.  Note the “Save” feature is deactivated until the software is purchased.
  • Interested in learning more about My Block Piecer and other Inspirations Software?  Join us at an Inspirations Event.  Click the Events link for events near you.
  • If you’re late to the Block of the Month “party” have no fear!  Start with Block 3 or spend a little time catching up.

Let’s continue the journey of learning and creativity!


Block 3 is our first two-unit block in the My Block Piecer Sampler Block of the Month. My Block Piecer splits some blocks into smaller units when a patch shares seam allowances with more than one patch. The 4-Triangle block consists of four half-square triangles. We’ll piece two units of two half-square triangles in the hoop. Then the units will be removed from the hoop and sewn together on the sewing machine with ¼” seam allowance. Let’s get started on Block 3.

  1. Open MBP.
  2. Click on Create a New Design.
  3. If the units for the ruler on the design page show mm, Right Click on either one of the rulers on the Design Page, and Click on Inches.
  4. Right Click on either ruler again and click on Grid Settings.
    1. Check marks by:
      1. Maintain aspect ratio
      2. Snap to grid.
    2. Set horizontal spacing to 0.25.
  5. Click on the Block icon.
    1. Enter 4 Triangles in the Find box at the bottom of the window. (DO NOT CLICK THE ENTER KEY).
    2. Click on the Down green arrow.
    3. Click OK to place the block on the design page.
  6. In the Properties Window on the right side of the screen, Click on the Transform icon.

    1. Have Maintain aspect ratio checked.
    2. Change the Width to 6.
    3. Click Apply.
  7. Click on the Select icon and holding down the CTRL key, select all of the patches.
  8. Click on the Workflow icon.

    1. Select a 200mm x 200 mm hoop or similar for your machine.
    2. Click the Auto Build button. Notice the block has been split into two units.
      Click Sort numbers. Select Yes in the message box.
    3. The numbers have been sorted according to the order they will be added to the block.
    4. Click Preview. The patch is split into two units. Both units will be created in one hooping. The second hooping (if you choice to use the hoop) will piece the two units together. Click Preview again.

      1. Click Save. Name the new folder Blk3Triangle and save it the format appropriate for your machine.
      2. A window will open showing you the files that are created.
        1. Blk3Triangles_001.pes (First Hooping).
        2. Block3Triangles_002.pes (Second Hooping)
        3. Blk3Triangle_artwork.c2s. (original block)
        4. 4_Triangles_preview.pdf. (stitching instructions)
      3. Close the file window.
    5. Close the Save window.
  9. Click the Cutter icon.

    1. Seam allowance default is .25”. Normally I change this to 0.4” or 0.5”, to make it easier to place the fabric pieces no matter which output format I choose.
    2. How you are going create the fabric pieces for the block, will determine which file format (hoop) to choose for the templates.
      1. If printing templates to manually cut the fabric pieces, select the Paper Letter 210×279.
      2. If using the Scan and Cut, select Brother SCN 12x12” or 12 x24”.
      3. If using the Silhouette, select Silhouette 12x12” or 12x24”.
    3. Can Unclick Optimize Orientation if using a directional fabric (This will optimize how the pieces file on the paper).
    4. If making four blocks for the large quilt, change 1 to 4 in the Repeat field.
    5. Click Apply.
    6. Click Save.
      1. In File name enter Blk3TriangleCut.
      2. Save the file in the format appropriate for your digital cutter.
      3. The Following Files are created for the Brother Scan n Cut.

        1. Blk3TriangleCut_001_1_1. (First Fabric)
        2. Blk3TriangleCut_002_2_1 (Second Fabric)
        3. Blk3TriangleCut_preview.pdf.
      4. Close the files window.
      5. Close the Cutter window.
  10. Print the templates, or prepare your fabric and send the templates to your cutter.
  11. Load the design in your machine and have fun making this block.

 

 

 

Block of the Month: Block 2 – Nested Triangles – Sewing Instruction

Block of the Month : Block 2 Nested Triangles
Sewing Instructions

If you missed the software lesson for Block 2, click here.


 

Hoop lightweight tear-away stabilizer or polymesh cut-away. Stitch color 1, the block diagram.

Place the patch 1 fabric, right side up, over patch 1. Stitch color 2, the tackdown.

Place the patch 2 fabric, right side down, over the seam of patches 1 and 2, aligning the seam allowances. Stitch color 3, the seam.

Flip patch 2 open and finger press the seam. Stitch color 4, the tackdown of patch 2.

Place the patch 3 fabric, right side down, over the seam of patches 2 and 3, aligning the seam allowances. Stitch color 5, the seam.

Flip patch 3 open and finger press the seam. Stitch color 6, the tackdown of patch 3.

Place the patch 4 fabric, right side down, over the seam of patches 1 and 3, aligning the seam allowances. Stitch color 7, the seam.

Flip patch 4 open and finger press the seam. Stitch color 8, the tackdown of patch 4.

Place the patch 5 fabric, right side down, over the seam of patches 2 and 5, aligning the seam allowances. Stitch color 9, the seam.

Flip patch 5 open and finger press the seam. Stitch color 10, the tackdown of patch 5.

Remove the hoop from the machine and the fabric from the hoop. Place the edge quilter’s ruler on the outside stitch line of the block. Trim the block on all sides. If you used tear-away stabilizer, remove it from the behind the patches. If a cut-away was used it will remain in the block.

If making the larger quilt, make four blocks of Nested Triangles. Piece the blocks with ¼” seam allowance or wait until all of your blocks are complete for the final assembly.

Variations on Block 2

Created by Nancy Stansbury

 

 

Block of the Month: Block 2 – Nested Triangles – Software Instruction

My Block Piecer Block of the Month: Block 2 Nested Triangles
Software Instructions
By Nancy Stansbury

We hope you are enjoying this Block of the Month series.  As a reminder, the first Saturday of every month will feature the software lesson using My Block Piecer.  The following Wednesday will feature the sewing lesson.

  • You are free to adapt the block to a size of your preference.
  • A free trial of My Block Piecer is available if you’d like to try it before you buy it.  Note the “Save” feature is deactivated until the software is purchased.
  • Interested in learning more about My Block Piecer and other Inspirations Software?  Join us at an Inspirations Event.  Click the Events link for events near you.

Let’s begin!


  1. Open MBP.
  2. Click on Create a New Design
  3. If the units for the ruler on the design page show mm, Right Click on either one of the rulers on the Design Page, and Click on Inches.
  4. Right Click on either ruler again and click on Grid Settings.
    1. Check marks by:
      1. Maintain aspect ratio
      2. Snap to grid.
    2. Set Horizontal spacing to 0.25.
    3. Click OK.
  5. Click on the Block icon.
    1. Enter Nested Triangles in the Find box at the bottom of the window (DO NOT CLICK THE ENTER KEY).
    2. Click on the Down green arrow.
    3. Click OK to place the block on the design page.
  6. In the Properties Window on the right side of the screen click on the Transform icon. noimage

    1. Have Maintain aspect ratio checked.
    2. Change the Width to 6.
    3. Click Apply.
  7. Click on the Select icon and draw a box around the block or Click CTRL-A.
  8. Click on the Workflow icon.

    1. Select a 200mm x 200 mm hoop or similar for your machine.
    2. Click the Auto Build button
  9. Click Sort Numbers. Select Yes in the message box.

    1. The numbers have been sorted to the order you will add them to the block.
  10. Click Preview. I’ve filled in patch 1 with green for easy detection. On your file, look for the green outline. Click Save, located under Preview.

    1. Click on Create a New Folder icon and name it Blk2Sew.
    2. Double Click on the folder to open it.
    3. In the File name box enter Blk2Sew.
    4. Click on the drop down menu next to Save and select the format for your machine.
    5. Click Save.
    6. A window will open showing you the files that have been created.

      1. Blk2Sew_001.pes.(stitch file for your machine)
      2. Blk2Sew _artwork.c2s. (original block)
      3. Blk2Sew _preview.pdf. (sewing instructions)
    7. Close the file window.
    8. Close the Save window.
  11. Click the Cutter icon.

    1. Seam allowance default is .25”. Normally I change this to 0.4” or 0.5”, to make it easier to place the fabric pieces no matter which cutting format I choose.
    2. How you are going to cut the fabric pieces for the block will determine which file format (hoop) to choose for the templates.
      1. If printing templates to manually cut the fabric pieces, select the Paper Letter 210×279.
      2. If using the Scan and Cut, select Brother SCN 12x12” or 12x24”.
      3. If using the Silhouette, select Silhouette 12x12”.
    3. Can Unclick Optimize Orientation if using a directional fabric (This will optimize how the pieces file on the paper.
    4. If making the large quilt, change 1 to 4 in the Repeats field.
    5. Click Apply. Click Save.
    6. In the File name, enter Blk2Templates (or something similar) and select the appropriate format from the drop down menu.
  12. The software will create files for your digital cutter or PDF patterns for printing on paper.
  13. Print the templates or prepare your fabric and send the digital cutting files to your cutter.
  14. Next lesson: stitching!

Block of the Month: Block 1 Peony – Sewing Instruction

My Block Piecer Sampler Quilt
Block of the Month : Block 1 Peony
Sewing Instructions

Tips to Keep in Mind

The first color of any My Block Piecer block is the block diagram. The diagram includes the numbers on the patches, the patches outlines and seam allowances. It’s helpful to stitch the diagram in a thread that you can see – something other than white (assuming your stabilizer is white). However, if your fabric is light-colored, the stitches could be visible through the fabric. Our photography shows the diagram in a contrasting color so you can see it clearly for instruction purposes. For this block, we used black and jewel tone fabrics so there is no worry about thread bleed-through.

A modern approach to the Block of Month Sampler includes pastel batiks and whites. A light-colored thread was selected for the diagram. It’s still visible to the user but won’t bleed through the fabrics.

We used a lightweight tear-away stabilizer that practically dissolves when washed so we won’t remove it after making the block. It’s up to you whether you want to take the time to remove the tear-away or leave it in the block. If you used a lightweight cut-away, such as poly mesh, you would not remove it.

In the software lesson for Block 1, you’ll remember that I cut my fabrics slightly larger than the standard ¼” seam allowance. That’s not mandatory but it is helpful.

The patches in the images below were cut with ¼” seam allowances. You can see how easy it is to misaligned the fabrics when working with a narrow seam allowance. In the first image, I ripped out the stitches and realigned the patch.

In the second image, I left the patch intact.

Let’s get started.

Hoop lightweight tear-away stabilizer or polymesh cut-away. Stitch color 1, the block diagram.

Place the patch 1 fabric, right side up, over patch 1. Stitch color 2, the tackdown.

Place the patch 2 fabric, right side down, over the seam of patches 1 and 2, aligning the seam allowances. Stitch color 3, the seam.

Flip patch 2 open and finger press the seam. Stitch color 4, the tackdown of patch 2.

Place the patch 3 fabric, right side down, over the seam of patches 2 and 3, aligning the seam allowances. Stitch color 5, the seam.

Flip patch 3 open and finger press the seam. Stitch color 6, the tackdown of patch 3.

Place the patch 4 fabric, right side down, over the seam of patches 3 and 4, aligning the seam allowances. Stitch color 7, the seam.

Flip patch 4 open and finger press the seam. Stitch color 8, the tackdown of patch 4.

Place the patch 5 fabric, right side down, over the seam of patches 4 and 5, aligning the seam allowances. Stitch color 9, the seam.

Flip patch 5 open and finger press the seam. Stitch color 10, the tackdown of patch 5.

Place the patch 6 fabric, right side down, over the seam of patches 1, 2, 4 and 5, aligning the seam allowances. Stitch color 11, the seam.

Flip patch 6 open and finger press the seam. Stitch color 12, the tackdown of patch 6.

Remove the hoop from the machine and the fabric from the hoop. Place the ¼” mark of a quilter’s ruler on the outside stitch line of the block. Trim the block on all sides. If you used a tear-away stabilizer and want to remove it, do it now. If a cut-away was used, it will remain in the block.

If making the larger quilt, make four blocks of Peony #2. Piece the blocks with ¼” seam allowance or wait until all of your blocks are complete for the final assembly.

Variations of Block 1 Assembly for Large Quilt

     

     

 

 

 

My Block Piecer Sampler Quilt Block of the Month

What’s the key to learning and improving your embroidery skills?  Practice!  The My Block Piecer Sampler Quilt block of the month will help you do just that!  Learn the ins and outs to creating in-the-hoop quilt blocks with My Block Piecer, one of today’s hottest techniques. You’ll get familiar with one-unit blocks, advance to two- unit block and three-unit blocks. You’ll learn how to create in-the-hoop blocks from the block library and original artwork files. Plus you’ll create borders – perfectly proportioned without the math!

Don’t have the software?  You can download a free trial by clicking here.  You’ll enjoy a fully-functioning software with only the “Save Function” disabled.  Once you’re ready to purchase the software, visit an Inspirations Dealer to make the purchase. After you purchase, you can duplicate the quilt shown here over the next 12 months.

This block of the month series will feature two lessons every month:

Software Lesson:  First Saturday of the Month
Sewing Lesson:  To be published the following Wednesday

This block of the month sampler quilt has unlimited potential: scrappy, monochromatic, jewel tone, batiks, or ultra-modern quilt.

All blocks are a 6” finished square and the border blocks are 3” x 6” finished.  You can make one of each block or make four for a larger quilt.

Quilt Dimensions

  • Finished size: 24” x 30”
  • We opted to piece our quilt without sashing. If you plan on adding 1” wide finished sashing, you’ll need 1/3 yd. of fabric for the sashing.
  • Fabric requirements:

This is a great opportunity to use scraps or select your own palette. You could go for a bright sunny look as shown above or opt for medium and dark jewel tones.  The image below shows a 42″ x 54″ version. In this version, you’ll make four repeats of each block.  If you opt for the larger quilt, double the yardage of each fabric.

Of course, you can never go wrong with an array of blues.

Yardage calculations are based on ¼” seam allowances. We have slightly increased the amounts for each fabric to allow some wiggle room for cutting and seam allowance.

Special thanks to Nancy Stansbury for this Block of the Month Series.


My Block Piecer Sampler Quilt
Block of the Month: Block 1 Peony
Software Instructions

  1. Open MBP.
  2. Click on Create a New Design.
    noimage
  3. If the units for the ruler on the design page show mm, Right Click on either one of the rulers on the Design Page, and Click on Inches.
  4. Right Click on either ruler again and click on Grid Settings.
    1. Check marks by:
      1. Maintain aspect ratio
      2. Snap to grid.
    2. Set horizontal spacing to 0.25.
  5. Click OK.
  6. Click on the Block icon. noimage
    noimage
  1. Enter Peony #2 in the Find box at the bottom of the window (DO NOT CLICK THE ENTER KEY). You’ll find Peony #2 under Foundation Blocks, Foundation Flowers. Remember to include the # sign as there are several Peony blocks in the Block Library.
  2. Click on the Down green arrow, next to the Find box.
  3. Click OK to place the block on the design page.noimage
  • In the Properties Window on the right side of the screen, click on the Transform icon. noimage
    noimage

    1. Have Maintain aspect ratio checked.
    2. Change the Width to 6.
    3. Click Apply.
  • Click on the Select icon and draw a box around the entire block, OR Enter CTRL-A to select all of the block.
  • Click on the Workflow icon.
    noimage

    1. In the Hoop field, select a 200mm x 200 mm hoop or similar for your machine from the drop down box.
    2. Click the Auto Build button.
    3. Click on Sort numbers. Click Yes in the message box.
      noimage
    4. The numbers have been sorted according to the order you will add them to the block.
      noimage
    5. Click Preview. I’ve filled in patch 1 with green for easy detection. On your file, look for the green outline. Click Save, located under Preview.
      noimage
    6. The software will automatically create a new folder with three files: the stitch file (select the format for your machine), the artwork of the block and the stitching instructions in PDF format.
      noimage
    7. Close the file window.
    8. Close the Save window.
  • Click the Cutter icon. noimage
    noimage

    1. Seam allowance default is .25”. Normally I change this to 0.4” or 0.5”, to make it easier to place the fabric pieces no matter which output format I choose.
    2. How you are going create the fabric pieces for the block, will determine which file format (hoop) to choose for the templates.
      1. If printing templates and using them to manually cut the fabric pieces, select the Paper Letter 210×279 from the Hoop field.
      2. If using the Scan and Cut, select Brother SCN 12x12”.
      3. If using the Silhouette, select Silhouette 12x12”.
      4. For digital cutting files, change the repeat from 1 to 4 if you are making the large quilt.
    3. Can Unclick Optimize Orientation if using a directional fabric (This will optimize how the pieces file on the paper.)
    4. Click Apply.
    5. Click Save.
      1. In File name enter Peony Templates.
      2. Click Save.
      3. The Following Files are created.
        1. Peony templates.pdf.
        2. Peony templates_preview.pdf.
      4. Close the files window.
      5. Close the Cutter window.
  • Print the templates, or prepare your fabric and send the templates to your cutter.
  • Load the design in your machine and have fun making this block.

 

 

 

 

My Block Piecer Block of the Month Sampler

Toot, toot!  Beep, beep!  We’re happy to announce our My Block Piecer Block of the Month Sampler.AllblocksBL

I learned so much when I made this quilt designed by Nancy Stansbury. Nancy did a fabulous job of designing and writing the instructions. My tasks were to stitch each block, photograph the process and make it available to the dealers.  So please nudge your dealer to participate.  We want everyone who owns My Block Piecer to join in the fun. By the time you’ve completed all 12 blocks, you’ll be a My Block Piecer pro!

You’ll learn how to make one, two and three-unit blocks.block1BL

And if you’ve been hankering to learn how to upload a block of your own and turn it into an in-the-hoop pieced block, you’ll learn that in block 6.Blk6BL

I forced myself to cut my patches on a digital cutter and became so familiar with that process; I was tempted to throw away my rotary cutter!  This is the most precise quilt I ever made – I’m so proud of all my sharp points, matching seams and flawless seam allowances.  I know, I know, it’s practically cheating when you’re using digital files – everything is perfect!

The Sampler works well as a scrap quilt or even modern solids.  But I took a different path because I just melt at Kaffee Fasset’s use of colors. I threw caution to the wind and grabbed several bolts of his Free Spirit fabrics. They might not have been the best choice, several of the prints are very large for these small patches but I couldn’t resist. I paired his bright fabrics with black and I must say I’m pleased with the end result.  We’ll unveil the fully-quilted version soon – right now it’s sitting on my shortE.

If you decide to make the large version (four repeats of each block), you’ll have fun creating your own layout. I think block 11 was my favorite because it gave so many options for joining the blocks. Blk11aBLBlock11bBLBlock11cBL

So nudge your dealer and encourage them to join in the fun!

What Color Would You Select?

I’m in a quandary. I’m designing the quilting for the My Block Piecer Block of the Month Sampler. The quilt is pieced and I’m excited to load the quilt onto the shortE and get started. Here’s a look at the pieced quilt on the design wall. Please forgive the photography – I took this photo with my cell phone.2015-12-19_20-00-51

Here’s one quilting layout that I started in My Quilt Planner. This layout features the same designs on each block. 2015-12-19_19-40-36

I don’t know if this is the one that I’ll go with but it’s been fun playing with the feathers.
Here’s a preview of the feathers a quilt block.2015-12-19_19-28-22

But what color thread? I’ve eliminated black because I’d like the quilting to pop on the black patches. Shall I select bright pink, hot blue, neon green or orange? Should I try to go with one color for the whole quilt or select thread for each block? What would you do?

1 2 3